斯派莎克阀门
服务分类
 阀门知识
产品分类
 斯派莎克减压阀
 斯派莎克疏水阀
 斯派莎克球阀
 斯派莎克闸阀
 斯派莎克蝶阀
 斯派莎克法兰
 斯派莎克底阀
 斯派莎克止回阀
 斯派莎克截止阀
 斯派莎克过滤器
 斯派莎克铜阀门
 斯派莎克波纹管阀门
 业务联系
 人才招聘
 客服电话
 在线联系
首页 - 用户服务 - 阀门知识 
双金属片式疏水阀介绍

译文:
双金属片式疏水阀介绍 双金属片疏水阀的主要部件是双金属片感温元件,随蒸汽温度升降受热变形,推动阀芯开关阀门。双金属片式疏水阀设有调整螺栓,可根据需要调节使用温度,一般过冷度调整范围低于饱和温度15℃-30℃,背压率大于70%,能排不凝结气体,不怕冻,体积小,能抗水击,耐高压,任意位置都可安装。双金属片有疲劳性,需要经常调整。 当装置刚启动时,管道出现低温冷凝水,双金属片是平展的,阀芯在弹簧的弹力下,阀门处于开启位置。当冷凝水温度渐渐升高,双金属片感温起元件开始弯曲变形,并把阀芯推向关闭位置。在冷凝水达到饱和温度之前,疏水阀开始关闭。双金属片随蒸汽温度变化控制阀门开关,阻汽排水。

原文
Bimetal traps introduced The main components of the bimetal traps bimetal temperature sensing element and thermal deformation, to promote the spool off valves with steam temperature lift. Bimetal steam trap with the adjusting bolt, according to the need to regulate the use of temperature, generally cooling degree adjustment range is lower than the saturation temperature of 15 ℃ -30 ℃, the back pressure greater than 70% can be ranked, non-condensing gas, and not afraid of cold. , small size, resistant to water hammer, high pressure, any location can be installed. The bimetal fatigue need to be adjusted regularly. When the device has just started, the pipeline appears that the low-temperature condensate, the bimetallic strip is flattened, in the spring will, the spool valve in the open position. When the condensation water temperature gradually increased, bimetal temperature from the component bending deformation, and the spool to the closed position. Before the saturation temperature in the condensate, the trap began to close. With the steam temperature, the bimetal control valve switch, resistance of air drainage.

 上一条:金属波纹管阀门需要注意的问题     下一条:[推荐]杠杆浮球式蒸汽疏水阀的特点介绍
首页 | 关于我们 | 新闻资讯 | 网络营销 | 企业信息| Sitemap.txt | 客户服务 | 联系我们 | 网站地图
http://www.spskv.com Copyright ©2004-2013蒸汽疏水阀、斯派莎克阀门、波纹管阀门、蒸汽过滤器生产厂家--- 嘉兴斯派莎克阀门有限公司 版权所有
电话:0573-89056296  传真:0573-89056296  手机:13819071892  地址:嘉兴港区工业区  邮箱:spskv@spskv.com
友情链接:嘉兴斯派莎克阀门 台湾阀门 富山阀门 铁王公司 百度网页百度网页 百度知道百度知道 百度百科百度百科 百度贴吧百度贴吧 百度空间百度空间 百度文库百度文库
分享到: